(70% Engineering / 30% Buyer Strategy — no images, word-based engineering detail)
Analog signals in roll forming machines are small, sensitive, and easily corrupted.
They are commonly used for:
Hydraulic pressure feedback
Load cell systems
Speed reference signals
Temperature sensors
Tension control systems
Line speed feedback
Unlike digital inputs (ON/OFF), analog signals represent continuous values.
Even small electrical noise can cause:
False pressure alarms
Erratic speed control
Tension instability
Hydraulic oscillation
Servo instability
Scrap production
In VFD-heavy environments like roll forming lines, proper shielding is not optional.
It is mandatory engineering discipline.
This guide explains how to shield analog signals correctly in industrial roll forming systems.
Typical analog ranges:
4–20mA
0–10V
±10V (servo systems)
Noise sources in roll forming machines include:
VFD motor cables
Servo drives
Switching contactors
Hydraulic solenoids
Poor grounding systems
Long cable runs
Shared 0V references
Analog signals operate at low amplitude relative to industrial noise.
If shielding and grounding are wrong, the signal becomes unstable.
More noise resistant
Preferred for industrial environments
Can tolerate longer cable runs
More sensitive to noise
More sensitive to voltage drop
Not ideal for long runs in VFD environments
For roll forming lines, use 4–20mA wherever possible.
Correct cable must be:
Twisted pair
Shielded
Low capacitance
Industrial grade
Example construction (word-based):
Conductor A + Conductor B (twisted)
Aluminum foil shield
Drain wire
Outer jacket
Twisting reduces electromagnetic interference (EMI).
Shield prevents radiated noise from coupling into signal.
Critical principle:
Shield must be grounded at ONE end only.
Typical approach:
Field device → PLC cabinet
Shield connected to earth at cabinet only
Shield floating at sensor end
If grounded at both ends:
Ground loop forms → noise injection occurs.
Pressure Transmitter + → PLC AI+
Pressure Transmitter – → PLC AI–
Shield → Earth bar (cabinet side only)
No connection of shield to 0V.
Shield should terminate at dedicated shield clamp connected to earth bar.
Inside control panel:
Left duct → Power cables
Right duct → Signal cables
Field routing:
Analog cables must not run parallel to motor cables
If crossing required, cross at 90 degrees
Keep minimum separation distance (typically 200–300mm)
Motor cables produce high-frequency noise due to PWM switching.
Parallel routing induces interference.
Most critical rule in roll forming plants:
Never run analog signal cable in same tray as VFD motor cable.
VFD output cables emit:
High-frequency switching noise
Common mode currents
Harmonics
Encoder and analog cables are especially vulnerable.
Poor separation causes:
Hydraulic pressure spikes
False temperature readings
Erratic speed feedback
PLC analog modules typically have:
AI+
AI–
Analog common
Important:
Analog common must not be treated as protective earth.
Use structured grounding:
Protective Earth (PE) for shielding
0V reference for control circuits
Analog reference isolated where required
Mixing PE and 0V incorrectly creates ground loops.
Best practice:
Single earth bar inside cabinet.
All shield drains connect to this point.
Earth bar bonded to cabinet and plant ground.
Avoid:
Multiple earth points scattered through cabinet.
Star grounding reduces noise potential.
Pressure reading fluctuates during motor acceleration
Temperature spikes only when shear fires
Speed reference unstable at high RPM
PLC analog value oscillates ±5% randomly
Alarm triggers only when stacker runs
These symptoms usually indicate EMI coupling.
Best practice:
Use 360-degree shield clamp at cabinet entry.
Avoid:
Long pigtail wire from shield to terminal.
Long pigtails reduce shielding effectiveness at high frequencies.
If multiple analog signals share one multi-core cable:
Each pair must be individually twisted
Overall shield required
Avoid mixing analog and digital signals in same cable
Best practice:
One twisted shielded pair per analog signal.
Long runs increase susceptibility.
Recommendations:
Use 4–20mA instead of 0–10V
Increase conductor size
Ensure clean ground reference
Avoid routing near high-power conductors
Consider signal isolator modules
Isolation modules break ground loops.
High-end roll forming lines use isolated analog modules.
Advantages:
Break ground loop
Reduce common-mode noise
Improve stability
Cost is higher but improves reliability.
Step-by-step test:
Monitor analog value in PLC
Observe reading with drives OFF
Observe reading with drives ON
Observe reading during acceleration
Measure 24V stability
Check shield continuity
If reading shifts under VFD load, shielding or routing is suspect.
Hydraulic Pressure Transmitter → 4–20mA → PLC AI
If motor starts and pressure reading jumps ±10%:
Likely causes:
Shared cable tray with motor cable
Shield grounded both ends
Poor earth bonding
No shield clamp
Fix routing before modifying PLC scaling.
Roll forming environments include:
Metal dust
Oil mist
Vibration
Temperature fluctuations
Ensure:
Cable glands sealed
Shield termination secure
No loose braid exposed
Vibration can loosen shield clamp over time.
When purchasing a roll forming machine, verify:
4–20mA used instead of 0–10V where possible
Analog cables shielded and twisted
Shield terminated at single point
Analog and motor cables separated
Earth bar properly bonded
Isolated analog module used (if high precision required)
Documentation shows analog routing plan
No mixing of analog and high-power cables
Red flag:
“Analog cable runs in same tray as motor cables.”
That is poor engineering practice.
It is more resistant to electrical noise and voltage drop.
No. Ground at one end only to prevent ground loops.
No. Maintain separation and cross at 90 degrees if necessary.
EMI coupling from VFD cables into analog lines.
No. Shield should connect to protective earth, not signal common.
Using unshielded cable in VFD-heavy environment.
Analog signal stability in roll forming machines depends on:
Shielded twisted-pair cable
Single-point grounding
Proper separation from motor wiring
Clean 24V control power
Isolated analog modules when necessary
Structured cabinet layout
Improper shielding leads to:
False alarms
Hydraulic instability
Length control issues
Scrap production
Intermittent faults
In modern roll forming lines filled with VFDs and servo drives, shielding discipline directly protects production accuracy and uptime.
Copyright 2026 © Machine Matcher.