Commissioning Without Factory Approval — Does It Void Your Roll Forming Machine Warranty?

Commissioning a roll forming machine without factory approval — does it void warranty? Full guide to risks, liability & disputes.

Commissioning is one of the most critical stages in the lifecycle of a roll forming machine.

It is the point where:

• Mechanical systems are aligned

• Servo drives are tuned

• Encoder scaling is configured

• Hydraulic pressure is set

• Production tolerances are verified

• Speed is gradually increased

When a machine is commissioned without factory approval or supervision, disputes often follow.

Suppliers may state:

“Warranty void due to unauthorized commissioning.”

Buyers may argue:

“We followed the manual — the machine is defective.”

This page explains:

• What commissioning legally means

• When factory approval is required

• How self-commissioning affects warranty

• What errors commonly occur

• How liability is determined

What Is Commissioning in a Roll Forming Machine?

Commissioning is not simply turning the machine on.

It includes:

• Mechanical alignment verification

• Leveling confirmation

• Servo parameter configuration

• Encoder calibration

• Hydraulic system tuning

• Speed ramp programming

• Punch and shear synchronization

• Trial production validation

• Safety system verification

Commissioning establishes the machine’s baseline performance.

If done incorrectly, many problems can appear that look like manufacturing defects.

Why Factory Approval Matters

Most roll forming machine manufacturers include one of the following clauses in their warranty:

• Commissioning must be performed by factory engineer

• Commissioning must be supervised by manufacturer

• Written approval required before full production

• Unauthorized modification voids warranty

The reason is simple:

Improper commissioning can damage components or create performance errors.

Common Problems Caused by Unauthorized Commissioning

1. Incorrect Encoder Scaling

If scaling factor is set incorrectly:

• Cut length inaccurate

• Punch drift occurs

• Production quality inconsistent

Later disputes may appear as “machine fault” when calibration error is the real cause.

2. Improper Servo Tuning

Servo systems require:

• Acceleration ramp tuning

• Torque limit setting

• Position gain adjustment

If tuned aggressively:

• Feed slippage occurs

• Overcurrent faults appear

• Motor overheating occurs

If tuned too conservatively:

• Production speed lower than promised

Improper tuning may damage equipment.

3. Hydraulic Pressure Misconfiguration

If hydraulic system:

• Over-pressurized

• Under-pressurized

• Not flushed properly

It may cause:

• Pump failure

• Shear timing errors

• Seal damage

Hydraulic damage due to incorrect commissioning is typically not covered.

4. Skipping Mechanical Alignment Verification

Before operation, machines must be checked for:

• Stand squareness

• Shaft alignment

• Coupling alignment

• Frame leveling

If skipped:

• Bearing wear accelerates

• Panel quality issues appear

• Shaft stress increases

Misalignment caused by installation and not corrected during commissioning may void warranty.

5. Running at Full Speed Immediately

Some operators attempt:

• Immediate full-speed production

• High tensile material from day one

Without gradual ramp-up:

• Gearbox stress increases

• Motor overheats

• Vibration amplifies

Damage caused by overloading during initial startup may void warranty.

6. Software Parameter Changes Without Authorization

Altering:

• PLC code

• Safety logic

• Servo programming

• Length compensation factors

Without manufacturer approval often voids warranty.

Unauthorized modification clauses are common in contracts.

When Commissioning Without Approval Voids Warranty

Warranty may be void if:

• Contract explicitly requires factory commissioning

• Unauthorized changes made to control system

• Hydraulic or electrical settings altered beyond specification

• Machine operated outside rated parameters

• Damage directly linked to commissioning error

If written approval was required and not obtained, supplier may legally reject claim.

When Commissioning Without Approval Does NOT Void Warranty

Warranty may still apply if:

• Manual clearly allows self-commissioning

• Installation followed documented procedure

• No unauthorized modifications made

• Fault unrelated to commissioning

• No damage caused by parameter changes

Each case depends on contract terms and documented actions.

Common Warranty Dispute Scenarios

Scenario 1: Bearing Failure After Self-Commissioning

Supplier claims misalignment during commissioning.

If alignment was not documented, dispute becomes complex.

Scenario 2: Servo Fault After Parameter Changes

If operator modified acceleration ramp and motor failed, warranty may be denied.

Scenario 3: Length Inaccuracy

If encoder scaling incorrect but no hardware damage occurred, supplier may assist under technical support — but may not accept full liability.

Structured Commissioning Checklist (To Protect Warranty)

If commissioning without factory presence, document everything.

Step 1: Record Mechanical Alignment

Document:

• Base leveling measurements

• Stand alignment

• Shaft straightness

Keep written log.

Step 2: Record Electrical Verification

Confirm:

• Voltage levels

• Phase rotation

• Earthing

• Protection devices

Keep electrician certification.

Step 3: Record Servo & Encoder Settings

Document:

• Scaling factor

• Acceleration

• Torque limits

• Safety parameters

Step 4: Record Hydraulic Setup

Confirm:

• Oil type

• Pressure setting

• Temperature during startup

Step 5: Gradual Speed Ramp Log

Increase speed in stages.

Document:

• 10 m/min

• 20 m/min

• 30 m/min

• Maximum speed

Record vibration and load.

Step 6: Trial Production Samples

Keep first batch samples as reference baseline.

Real Case Example

A 30 m/min roofing machine commissioned by buyer without factory supervision developed gearbox failure within 3 months.

Supplier denied warranty, citing aggressive acceleration settings.

Investigation showed:

• Acceleration ramp doubled from factory default

• Motor current exceeded rated value

• No documented commissioning log

Warranty claim rejected.

Root cause: unauthorized parameter modification.

Protecting Yourself Before Commissioning

Before installing:

1. Confirm whether factory commissioning is mandatory

2. Clarify warranty impact of self-commissioning

3. Request written commissioning procedure

4. Ask for remote supervision option

5. Record full startup process

Clear communication prevents disputes.

Warning Signs of Improper Commissioning

• Immediate high-speed operation

• Servo alarms frequently

• Overheating in first week

• Hydraulic noise

• Length inconsistency from day one

• Excess vibration

Early correction prevents long-term damage.

Frequently Asked Questions

Does self-commissioning automatically void warranty?

Not always. It depends on contract terms.

Can changing PLC settings void warranty?

Yes — if unauthorized modification is prohibited in contract.

Should factory engineer supervise commissioning?

For high-speed or complex machines, it is strongly recommended.

Is remote commissioning acceptable?

Many suppliers allow supervised remote commissioning.

What is the biggest risk during commissioning?

Incorrect servo tuning and overloading during initial startup.

How can I protect my warranty?

Document everything and follow written commissioning procedure strictly.

Final Conclusion

Commissioning without factory approval does not automatically void warranty — but it significantly increases risk.

Many warranty disputes arise because:

• Parameters were changed

• Setup was rushed

• Alignment was skipped

• Speed increased too quickly

• Documentation was not kept

If damage or performance failure is directly linked to improper commissioning, warranty claims may be denied.

Clear communication, written approval, and structured documentation protect both buyer and manufacturer.

Without documented commissioning procedure, disputes become difficult to resolve.

With proper records, liability becomes clear.