16/1000 Roof Panel Roll Forming Machine Data Sheet | Specifications & Capacity
16/1000 Roof Panel Roll Forming Machine Technical Data Sheet
Machine Overview
Parameter Specification
Machine Name 16/1000 Roof Panel Roll Forming Machine
Profile Produced 16/1000 Metal Roof Panel
Machine Type Single profile / Double layer / Multi-profile
Production Application Residential roofing, wall cladding, light commercial roofing
Manufacturing Process Continuous cold roll forming
Production Environment Factory production line / portable system / containerized system
The 16/1000 roof panel roll forming machine is designed to manufacture low-profile trapezoidal metal roofing and cladding panels widely used in residential buildings and light commercial construction.
Production Specifications
Specification Typical Value
Production Speed 10–40 m/min
Forming Stations 14–20 stations
Material Thickness Range 0.3–0.55 mm
Coil Width 1150–1200 mm
Coil Weight Capacity 5–10 tons
Cut Length Tolerance ±1 mm
Minimum Panel Length 500 mm
Maximum Panel Length Unlimited
Production speed varies depending on material thickness, panel length, and machine configuration.
Material Compatibility
Material Type Supported
Galvanized Steel Yes
Pre-painted Steel Yes
Galvalume Steel Yes
Aluminum Optional
Stainless Steel Limited
Material Strength
Property Typical Range
Yield Strength G350 – G550
Tensile Strength Up to 550 MPa
Coating Types Z275 galvanized, AZ150 Galvalume, polyester paint, PVDF coatings
Machine Frame Construction
Component Specification
Frame Type Welded structural steel frame
Frame Plate Thickness 12–20 mm
Machine Base Heavy duty fabricated steel base
Frame Alignment Precision machined mounting surfaces
Machine Weight 6–11 tons
A rigid machine frame ensures consistent forming accuracy and stable production performance.
Roll Tooling Specifications
Specification Typical Value
Roller Material GCr15 bearing steel
Heat Treatment HRC 58–62
Roller Diameter 60–80 mm
Shaft Diameter 70–80 mm
Shaft Material 40Cr steel
Surface Finish Hard chrome plating
Roll Pass Design Progressive multi-stage forming
Forming Stages 14–20 stations
Drive System
Component Specification
Drive Type Chain drive / Gearbox drive
Main Motor 7.5–11 kW
Drive Ratio 1:20
Transmission Industrial gearbox
Lubrication Oil bath gearbox
Gearbox driven systems provide smooth operation and reliable torque transfer.
Hydraulic Cutting System
Component Specification
Cutting Type Hydraulic flying shear
Blade Material Cr12 tool steel
Cutting Accuracy ±1 mm
Hydraulic Pressure 10–16 MPa
Hydraulic Motor 4–5.5 kW
Flying shear cutting allows panels to be cut without stopping the roll forming process.
Control System
Component Specification
PLC Siemens / Delta / Mitsubishi
HMI Touch screen control interface
Length Measurement Rotary encoder
Control Accuracy ±1 mm
Automation Fully automatic production
Electrical Specifications
Parameter Value
Voltage 380V / 415V / 480V
Frequency 50 Hz / 60 Hz
Control Voltage 24V
Electrical Cabinet IP54 industrial enclosure
Protection Overload protection and circuit breakers
Machine Layout Dimensions
Parameter Value
Machine Length 6–10 m
Machine Width 1.5–2 m
Machine Height 1.5–2 m
Total Production Line Length 13–20 m
Typical production line configuration:
Uncoiler → Roll Forming Machine → Hydraulic Shear → Run-out Table
Coil Handling Equipment
Specification Value
Uncoiler Type Manual or hydraulic decoiler
Coil Capacity 5–10 tons
Coil Inner Diameter 450–550 mm
Coil Outer Diameter Up to 1500 mm
Expansion Type Hydraulic expansion
Optional Equipment
Equipment Description
Automatic Stacker Automated panel stacking
Double Layer Machine Two profiles in one machine
Coil Car Automatic coil loading system
Servo Feeder Precision feeding system
Automatic Packaging System Panel packaging system
Remote PLC Monitoring Remote diagnostics and monitoring
Installation Requirements
Requirement Typical
Foundation Reinforced concrete floor
Floor Load Capacity 4–8 tons
Electrical Connection Three phase industrial power supply
Air Supply Optional
Installation Time 2–3 days
Maintenance Requirements
Component Maintenance Interval
Gearbox Oil Every 6 months
Bearings Every 6 months
Hydraulic Oil Every 12 months
Roll Tooling Inspection Monthly
Routine maintenance ensures long machine life and stable panel production quality.
Production Capacity Example
Production Speed Output
15 m/min 900 m/hour
20 m/min 1200 m/hour
30 m/min 1800 m/hour
Actual output depends on panel length and material thickness.
16/1000 Roof Panel Profile Information
Specification Value
Coverage Width 1000 mm
Rib Height 16 mm
Rib Pitch 200 mm
Typical Gauge 0.3–0.5 mm
The 16/1000 roof panel profile is commonly used in residential roofing and wall cladding systems due to its lightweight design and wide coverage.
Machine Standards
Standard Description
CE Certification European machinery safety standards
ISO 9001 Manufacturing quality management
Electrical Compliance Industrial electrical safety standards
Shipping Information
Specification Value
Container Size 40 ft container
Shipping Weight 8–13 tons
Packaging Industrial export packing
Typical Machine Price Range
Machine Type Price Range
Basic Line $32,000 – $48,000
Automatic Line $48,000 – $70,000
High Speed Line $80,000+
Pricing depends on machine speed, automation level, and tooling configuration.
Applications
Industry Use
Residential Roofing Housing developments
Commercial Roofing Small warehouses and retail buildings
Wall Cladding Agricultural and commercial structures
Light Industrial Buildings Workshops and storage facilities
The 16/1000 roof panel profile is widely manufactured in Europe, Africa, Asia, and South America for residential roofing and cladding applications.