Clip Lock Standing Seam Roll Forming Machine Data Sheet | Specifications & Capacity
Clip Lock Standing Seam Roll Forming Machine Technical Data Sheet
Machine Overview
Parameter Specification
Machine Name Clip Lock Standing Seam Roll Forming Machine
Profile Produced Clip Lock Standing Seam Roof Panel
Machine Type Single profile / Adjustable profile machine
Production Application Commercial roofing, architectural roofing, industrial roofing systems
Manufacturing Process Continuous cold roll forming
Production Environment Factory production line / portable job site machine / containerized system
The clip lock standing seam roll forming machine produces concealed fastener standing seam roofing panels that are secured to the roof structure using metal clips. This system allows thermal movement of the roof panels while maintaining strong wind uplift resistance.
Production Specifications
Specification Typical Value
Production Speed 10–35 m/min
Forming Stations 18–26 stations
Material Thickness Range 0.4–0.9 mm
Coil Width 400–650 mm
Coil Weight Capacity 3–8 tons
Cut Length Tolerance ±1 mm
Minimum Panel Length 500 mm
Maximum Panel Length Unlimited
Clip lock machines are commonly used for both factory production and portable job-site roll forming.
Material Compatibility
Material Type Supported
Galvanized Steel Yes
Pre-painted Steel Yes
Galvalume Steel Yes
Aluminum Yes
Copper Optional
Zinc Optional
Material Strength
Property Typical Range
Yield Strength G250 – G550
Tensile Strength Up to 550 MPa
Coating Types PVDF coatings, SMP coatings, Galvalume AZ150
These coatings provide corrosion resistance and long service life for roofing systems.
Machine Frame Construction
Component Specification
Frame Type Precision welded structural steel frame
Frame Plate Thickness 14–22 mm
Machine Base Heavy duty fabricated steel base
Frame Alignment Precision machined mounting surfaces
Machine Weight 7–13 tons
The rigid frame design ensures accurate seam geometry and consistent panel forming.
Roll Tooling Specifications
Specification Typical Value
Roller Material GCr15 bearing steel
Heat Treatment HRC 58–62
Roller Diameter 65–90 mm
Shaft Diameter 70–90 mm
Shaft Material 40Cr alloy steel
Surface Finish Hard chrome plating
Roll Pass Design Progressive standing seam forming
Forming Stages 18–26 stations
Roll tooling forms the vertical seams designed to engage with concealed clips.
Drive System
Component Specification
Drive Type Chain drive / gearbox drive
Main Motor 7.5–15 kW
Drive Ratio 1:20
Transmission Industrial gearbox
Lubrication Oil bath gearbox
The drive system provides smooth forming and consistent panel dimensions.
Hydraulic Cutting System
Component Specification
Cutting Type Hydraulic flying shear
Blade Material Cr12 tool steel
Cutting Accuracy ±1 mm
Hydraulic Pressure 10–16 MPa
Hydraulic Motor 4–5.5 kW
Flying shear cutting allows panels to be cut while production continues.
Control System
Component Specification
PLC Siemens / Delta / Mitsubishi
HMI Touch screen control interface
Length Measurement Rotary encoder system
Control Accuracy ±1 mm
Automation Fully automatic production
Control functions include:
Automatic length control
Batch production programming
Fault diagnostics
Emergency stop system
Electrical Specifications
Parameter Value
Voltage 380V / 415V / 480V
Frequency 50 Hz / 60 Hz
Control Voltage 24V
Electrical Cabinet IP54 industrial enclosure
Protection Overload protection and circuit breakers
Machine Layout Dimensions
Parameter Value
Machine Length 8–12 m
Machine Width 1.5–2 m
Machine Height 1.5–2 m
Total Production Line Length 14–20 m
Typical production line configuration:
Uncoiler → Standing Seam Roll Forming Machine → Hydraulic Shear → Run-out Table
Portable machines may produce panels directly on construction sites.
Coil Handling Equipment
Specification Value
Uncoiler Type Manual or hydraulic decoiler
Coil Capacity 3–8 tons
Coil Inner Diameter 450–550 mm
Coil Outer Diameter Up to 1500 mm
Expansion Type Hydraulic expansion
Optional Equipment
Equipment Description
Automatic Stacker Automated panel stacking system
Portable Roll Former Job-site roll forming machine
Coil Car Automatic coil loading system
Servo Feeder Precision feeding system
Remote PLC Monitoring Remote diagnostics and monitoring
Installation Requirements
Requirement Typical
Foundation Reinforced concrete floor
Floor Load Capacity 5–8 tons
Electrical Connection Three phase industrial power supply
Air Supply Optional
Installation Time 2–3 days
Portable machines may require minimal installation.
Maintenance Requirements
Component Maintenance Interval
Gearbox Oil Every 6 months
Bearings Every 6 months
Hydraulic Oil Every 12 months
Roll Tooling Inspection Monthly
Regular maintenance ensures consistent seam quality and long machine service life.
Production Capacity Example
Production Speed Output
15 m/min 900 m/hour
20 m/min 1200 m/hour
30 m/min 1800 m/hour
Actual production output depends on panel length and material thickness.
Clip Lock Standing Seam Profile Information
Specification Value
Panel Coverage Width 300–450 mm
Seam Height 25–65 mm
Fastening Method Concealed clip fastening system
Typical Gauge 24–22 gauge
Clip lock standing seam panels allow thermal expansion and contraction while maintaining strong structural attachment.
Machine Standards
Standard Description
CE Certification European machinery safety standards
ISO 9001 Manufacturing quality management
Electrical Compliance Industrial electrical safety standards
Shipping Information
Specification Value
Container Size 40 ft container
Shipping Weight 10–14 tons
Packaging Industrial export packing
Portable machines may ship in smaller containers.
Typical Machine Price Range
Machine Type Price Range
Standard Line $45,000 – $70,000
Automatic Line $70,000 – $100,000
High Speed Line $110,000+
Pricing varies depending on automation level, machine speed, and tooling configuration.
Applications
Industry Use
Commercial Roofing Office buildings and retail structures
Industrial Roofing Warehouses and manufacturing facilities
Architectural Roofing Modern architectural metal roofs
Institutional Buildings Schools, hospitals, and public buildings
Clip lock standing seam roofing systems are widely used worldwide due to their concealed fastening system, thermal expansion capability, and high wind uplift resistance.