Nail Strip Standing Seam Roll Forming Machine Data Sheet | Specifications & Capacity
Nail Strip Standing Seam Roll Forming Machine Technical Data Sheet
Machine Overview
Parameter Specification
Machine Name Nail Strip Standing Seam Roll Forming Machine
Profile Produced Nail Strip Standing Seam Metal Roof Panel
Machine Type Single profile / Adjustable profile machine
Production Application Residential roofing, architectural roofing, light commercial roofing
Manufacturing Process Continuous cold roll forming
Production Environment Factory production line / portable job site machine / containerized system
The nail strip standing seam roll forming machine produces concealed fastener roofing panels with an integrated fastening flange. This profile allows panels to be directly fastened to the roof deck without clips, simplifying installation.
Production Specifications
Specification Typical Value
Production Speed 10–35 m/min
Forming Stations 18–24 stations
Material Thickness Range 0.4–0.7 mm
Coil Width 400–650 mm
Coil Weight Capacity 3–8 tons
Cut Length Tolerance ±1 mm
Minimum Panel Length 500 mm
Maximum Panel Length Unlimited
Nail strip machines are often used in portable roll forming systems producing panels directly at construction sites.
Material Compatibility
Material Type Supported
Galvanized Steel Yes
Pre-painted Steel Yes
Galvalume Steel Yes
Aluminum Yes
Copper Optional
Material Strength
Property Typical Range
Yield Strength G250 – G550
Tensile Strength Up to 550 MPa
Coating Types PVDF coatings, SMP coatings, Galvalume AZ150
High quality coatings are used to ensure long-term corrosion resistance for roofing applications.
Machine Frame Construction
Component Specification
Frame Type Welded structural steel frame
Frame Plate Thickness 14–22 mm
Machine Base Heavy duty fabricated base
Frame Alignment Precision machined mounting surfaces
Machine Weight 7–12 tons
The machine frame ensures accurate seam formation and panel geometry.
Roll Tooling Specifications
Specification Typical Value
Roller Material GCr15 bearing steel
Heat Treatment HRC 58–62
Roller Diameter 65–90 mm
Shaft Diameter 70–90 mm
Shaft Material 40Cr alloy steel
Surface Finish Hard chrome plating
Roll Pass Design Progressive standing seam forming
Forming Stages 18–24 stations
The roll tooling gradually forms the nail strip flange and vertical seams.
Drive System
Component Specification
Drive Type Chain drive / gearbox drive
Main Motor 7.5–15 kW
Drive Ratio 1:20
Transmission Industrial gearbox
Lubrication Oil bath gearbox
The drive system ensures smooth and consistent panel forming.
Hydraulic Cutting System
Component Specification
Cutting Type Hydraulic flying shear
Blade Material Cr12 tool steel
Cutting Accuracy ±1 mm
Hydraulic Pressure 10–16 MPa
Hydraulic Motor 4–5.5 kW
Flying shear cutting allows panels to be cut to length while production continues.
Control System
Component Specification
PLC Siemens / Delta / Mitsubishi
HMI Touch screen control interface
Length Measurement Rotary encoder
Control Accuracy ±1 mm
Automation Fully automatic production
Functions include:
Automatic length control
Batch production programming
Fault diagnostics
Emergency stop system
Electrical Specifications
Parameter Value
Voltage 380V / 415V / 480V
Frequency 50 Hz / 60 Hz
Control Voltage 24V
Electrical Cabinet IP54 industrial enclosure
Protection Overload protection and circuit breakers
Machine Layout Dimensions
Parameter Value
Machine Length 8–12 m
Machine Width 1.5–2 m
Machine Height 1.5–2 m
Total Production Line Length 14–20 m
Typical production line configuration:
Uncoiler → Standing Seam Roll Forming Machine → Hydraulic Shear → Run-out Table
Portable machines may integrate compact coil handling equipment.
Coil Handling Equipment
Specification Value
Uncoiler Type Manual or hydraulic decoiler
Coil Capacity 3–8 tons
Coil Inner Diameter 450–550 mm
Coil Outer Diameter Up to 1500 mm
Expansion Type Hydraulic expansion
Optional Equipment
Equipment Description
Automatic Stacker Automated panel stacking system
Portable Roll Former Job-site roll forming machine
Coil Car Automatic coil loading system
Servo Feeder Precision feeding system
Remote PLC Monitoring Remote diagnostics and monitoring
Installation Requirements
Requirement Typical
Foundation Reinforced concrete floor
Floor Load Capacity 5–8 tons
Electrical Connection Three phase industrial power supply
Air Supply Optional
Installation Time 2–3 days
Portable systems may require minimal installation.
Maintenance Requirements
Component Maintenance Interval
Gearbox Oil Every 6 months
Bearings Every 6 months
Hydraulic Oil Every 12 months
Roll Tooling Inspection Monthly
Routine maintenance ensures consistent panel production and seam accuracy.
Production Capacity Example
Production Speed Output
15 m/min 900 m/hour
20 m/min 1200 m/hour
30 m/min 1800 m/hour
Actual output depends on panel length and production setup.
Nail Strip Standing Seam Profile Information
Specification Value
Panel Coverage Width 300–450 mm
Seam Height 25–40 mm
Fastening Method Integrated nail strip flange
Typical Gauge 26–24 gauge
Nail strip standing seam panels allow faster installation because clips are not required.
Machine Standards
Standard Description
CE Certification European machinery safety standards
ISO 9001 Manufacturing quality management
Electrical Compliance Industrial electrical safety standards
Shipping Information
Specification Value
Container Size 40 ft container
Shipping Weight 10–14 tons
Packaging Industrial export packing
Portable machines may ship in smaller containers.
Typical Machine Price Range
Machine Type Price Range
Standard Line $45,000 – $70,000
Automatic Line $70,000 – $100,000
High Speed Line $110,000+
Pricing depends on machine configuration, automation level, and profile adjustability.
Applications
Industry Use
Residential Roofing Homes and residential buildings
Architectural Roofing High-end residential roofing projects
Light Commercial Roofing Small commercial buildings
Renovation Roofing Roof replacements and upgrades
Nail strip standing seam roofing systems are widely used for residential metal roofing due to their simplified installation and clean architectural appearance.