Micro Corrugated Panel Roll Forming Machine Data Sheet | Specifications & Capacity
Micro Corrugated Panel Roll Forming Machine Technical Data Sheet
Machine Overview
Parameter Specification
Machine Name Micro Corrugated Panel Roll Forming Machine
Profile Produced Micro Corrugated Metal Panel
Machine Type Single profile / Double layer / Multi-profile
Production Application Architectural cladding, interior wall panels, decorative panels, lightweight roofing
Manufacturing Process Continuous cold roll forming
Production Environment Factory production line / containerized system / compact production line
The micro corrugated panel roll forming machine is designed to produce fine corrugated metal sheets with small rib spacing. These panels are widely used in architectural metal cladding, interior design applications, and lightweight roofing systems.
Production Specifications
Specification Typical Value
Production Speed 10–40 m/min
Forming Stations 14–20 stations
Material Thickness Range 0.2–0.6 mm
Coil Width 600–1250 mm
Coil Weight Capacity 3–8 tons
Cut Length Tolerance ±1 mm
Minimum Panel Length 500 mm
Maximum Panel Length Unlimited
Production speed depends on material thickness and panel length.
Material Compatibility
Material Type Supported
Galvanized Steel Yes
Pre-painted Steel Yes
Galvalume Steel Yes
Aluminum Yes
Stainless Steel Optional
Material Strength
Property Typical Range
Yield Strength G250 – G550
Tensile Strength Up to 550 MPa
Coating Types Z275 galvanized, AZ150 Galvalume, polyester paint, PVDF coatings
Machine Frame Construction
Component Specification
Frame Type Welded structural steel frame
Frame Plate Thickness 12–18 mm
Machine Base Heavy duty fabricated steel base
Frame Alignment Precision machined mounting surfaces
Machine Weight 6–10 tons
The compact machine frame allows stable production of fine corrugated panels with high dimensional accuracy.
Roll Tooling Specifications
Specification Typical Value
Roller Material GCr15 bearing steel
Heat Treatment HRC 58–62
Roller Diameter 60–75 mm
Shaft Diameter 65–80 mm
Shaft Material 40Cr steel
Surface Finish Hard chrome plating
Roll Pass Design Fine sinusoidal progressive forming
Forming Stages 14–20 stations
Drive System
Component Specification
Drive Type Chain drive / gearbox drive
Main Motor 5.5–11 kW
Drive Ratio 1:20
Transmission Industrial gearbox
Lubrication Oil bath gearbox
The drive system provides smooth and consistent forming for fine rib profiles.
Hydraulic Cutting System
Component Specification
Cutting Type Hydraulic flying shear
Blade Material Cr12 tool steel
Cutting Accuracy ±1 mm
Hydraulic Pressure 10–16 MPa
Hydraulic Motor 3–5.5 kW
Flying shear cutting allows continuous production without stopping the roll forming process.
Control System
Component Specification
PLC Siemens / Delta / Mitsubishi
HMI Touch screen control interface
Length Measurement Rotary encoder
Control Accuracy ±1 mm
Automation Fully automatic production
Electrical Specifications
Parameter Value
Voltage 380V / 415V / 480V
Frequency 50 Hz / 60 Hz
Control Voltage 24V
Electrical Cabinet IP54 industrial enclosure
Protection Overload protection and circuit breakers
Machine Layout Dimensions
Parameter Value
Machine Length 6–9 m
Machine Width 1.5–2 m
Machine Height 1.5–2 m
Total Production Line Length 12–18 m
Typical production line configuration:
Uncoiler → Micro Corrugated Roll Forming Machine → Hydraulic Shear → Run-out Table
Coil Handling Equipment
Specification Value
Uncoiler Type Manual or hydraulic decoiler
Coil Capacity 3–8 tons
Coil Inner Diameter 450–550 mm
Coil Outer Diameter Up to 1500 mm
Expansion Type Hydraulic expansion
Optional Equipment
Equipment Description
Automatic Stacker Automated sheet stacking system
Double Layer Machine Two profiles in one machine
Coil Car Automatic coil loading system
Servo Feeder Precision feeding system
Automatic Packaging System Panel packaging system
Remote PLC Monitoring Remote diagnostics and monitoring
Installation Requirements
Requirement Typical
Foundation Reinforced concrete floor
Floor Load Capacity 4–8 tons
Electrical Connection Three phase industrial power supply
Air Supply Optional
Installation Time 2–3 days
Maintenance Requirements
Component Maintenance Interval
Gearbox Oil Every 6 months
Bearings Every 6 months
Hydraulic Oil Every 12 months
Roll Tooling Inspection Monthly
Routine maintenance ensures stable panel quality and long machine service life.
Production Capacity Example
Production Speed Output
15 m/min 900 m/hour
20 m/min 1200 m/hour
30 m/min 1800 m/hour
Actual output depends on panel length and material thickness.
Micro Corrugated Panel Profile Information
Specification Value
Coverage Width 600–1000 mm
Corrugation Height 3–10 mm
Corrugation Pitch 15–35 mm
Typical Gauge 0.2–0.5 mm
Micro corrugated panels are widely used for architectural metal cladding and decorative wall systems.
Machine Standards
Standard Description
CE Certification European machinery safety standards
ISO 9001 Manufacturing quality management
Electrical Compliance Industrial electrical safety standards
Shipping Information
Specification Value
Container Size 40 ft container
Shipping Weight 8–12 tons
Packaging Industrial export packing
Typical Machine Price Range
Machine Type Price Range
Standard Line $30,000 – $45,000
Automatic Line $45,000 – $65,000
High Speed Line $75,000+
Pricing varies depending on machine speed, automation level, and tooling configuration.
Applications
Industry Use
Architectural Cladding Decorative metal façade panels
Interior Design Interior wall and ceiling panels
Residential Roofing Lightweight roofing systems
Commercial Buildings Architectural metal cladding systems
Micro corrugated metal panels are widely produced across Europe, North America, Asia, and Australia for architectural applications due to their aesthetic appearance and lightweight construction.